Renew Troubleshooting Cisco Data Center Infrastructure (DCIT) 300-615 Question

NEW QUESTION 1
An attempt to use a global vNIC redundancy template pair results in a service profile that fails to apply. Which action resolves the issues?

• A. Create the peer names before creating the templates.
• B. Assign the secondary template first, and then set the peer name.
• C. Assign both templates simultaneously.
• D. Assign the primary template first, and then set the peer name.

Answer: D

NEW QUESTION 2
An engineer removes a VMM domain from an endpoint group called EPG-1, but the distributed port group fails to be deleted. Which action must be taken to resolve the issue?

• A. Remove the port group manually.
• B. Migrate all virtual machines in the EPG-1 to different hypervisors.
• C. Remove the remaining EPGs from the VMM domain.
• D. Migrate all virtual machines in the EPG-1 to different port groups.

Answer: C

NEW QUESTION 3
DRAG DROP
Drag and drop the actions from the left onto the faults that they resolve on the right. Not all options are used.
Select and Place:

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 4

Refer to the exhibit. The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID 0x970200. What action resolves the issue?

• A. Reconfigure the initiator and the target to be in the same zones.
• B. Reactivate the zoneset.
• C. Reset the port for FC ID 0x970102 and FC ID 0x970200 to log in to the fabric.
• D. Reset the port for FC ID 0x970209 and FC ID 0x9700c2 to log in to the fabric.

Answer: B

NEW QUESTION 5

Refer to an exhibit. An engineer is troubleshooting an upgrade failure on a switch. Which action resolves the issue?

• A. Save the system image in NVRAM.
• B. Use the same system image as the kickstart image.
• C. Load a new system image.
• D. Reload the same system image.

Answer: C

NEW QUESTION 6
A fabric interconnect fails to start and the console displays the loader prompt. Which two actions resolve the issue? (Choose two.)

• A. Load an uncorrupt bootloader image.
• B. Load an uncorrupt kickstart image.
• C. Reconnect L1/L2 cables between the Fis.
• D. Reformat the fabric interconnect.
• E. Load the correct version of the boot image.

Answer: BE

NEW QUESTION 7
A request to activate the port security database is rejected. Which action do you perform to investigate the cause of the issue?

• A. Enable the auto-learning feature.
• B. Use the force option to identify rejected devices.
• C. Find conflicting entries between the active and configuration databases.
• D. Verify that devices are fully attached to the active database.

Answer: B

NEW QUESTION 8
An IOM fails during a firmware upgrade and is unresponsive. Which action recovers the module?

• A. Restore UCSM configuration from backup.
• B. Roll back to the previous firmware.
• C. Use AutoInstall to reinstall the firmware.
• D. From the peer IOM, reset the faulty module.

Answer: B

NEW QUESTION 9
Your client reports that many flaps and server cluster disconnects occur in their data center. While troubleshooting the issue, you discover a network attack hitting their Cisco Nexus 7000 Series Switches and determine that the source IP addresses are spoofed. Which first-line security solution resolves this issue?

• A. Dynamic ARP Inspection
• B. Unicast RPF
• C. IP Source Guard
• D. Storm Control

Answer: A

NEW QUESTION 10
After upgrading a client’s fabric interconnect to the latest version, an engineer discovers that the appliance has lost its entire configuration. Which two locations should an engineer check to confirm that the appliance had backed up the configuration prior to the upgrade in order to retrieve the lost configuration? (Choose two.)

• A. Equipment FSM page, InternalBackup stage
• B. Service profiles page, InternalBackup stage
• C. Admin page, PollInternalBackup stage
• D. Equipment FSM page, PollInternalBackup stage
• E. Admin page, InternalBackup stage.

Answer: AC

NEW QUESTION 11

Refer to the exhibit. The HSRP instance on both switches is showing as active. Which action resolves the issue?

• A. Configure the HSRP timers to be the same.
• B. Allow VLAN 100 between the switches.
• C. Configure the IP address of N9K-B on the same subnet as N9K-A.
• D. Configure preempt on only one of the switches.

Answer: B

NEW QUESTION 12
An engineer is troubleshooting a failed DCBX exchange between a server and a Cisco Nexus switch. Which action allows DCBX to successfully negotiate?

• A. Enable ETS
• B. Enable PFC.
• C. Enable Cisco Discovery Protocol.
• D. Enable LLDP.

Answer: D

NEW QUESTION 13
A server fails to boot from the operating system after a RAID1 cluster migration. The RAID remains in an inactive state during and after a service profile association. Which action resolves the issue?

• A. Configure the SAN boot target in the service profile.
• B. Configure the SAN boot target to any configuration mode.
• C. Use a predefined local disk configuration policy.
• D. Remove the local disk configuration policy.

Answer: C

NEW QUESTION 14
An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After the replacement was done, the server has a “resolve slot” warning. Which server maintenance action resolves the issue?

• A. Perform diagnostic interrupt on the server.
• B. Re-acknowlegement the server.
• C. Reset the server.
• D. Decomission the server.

Answer: B

NEW QUESTION 15
The Cisco Nexus switch is connected to a peer switch that is not running Cisco NX-OS. The switches are connected using port channel and are experiencing packet loss. Which action should be performed on the Cisco Nexus switch ports to resolve this issue?

• A. Turn on lacp suspend-individual.
• B. Turn on lacp graceful-convergence.
• C. Turn off lacp graceful-convergence.
• D. Turn off lacp suspend-individual.

Answer: C

NEW QUESTION 16

Refer to the exhibit. An engineer is troubleshooting why user1, user2, and user3 from group STORAGE-ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?

• A. Configure the role name to match the group name on Microsoft Active Directory.
• B. Include specific users into MDS role configuration.
• C. Configure SSH logins on Cisco MDS switch.
• D. Integrate Cisco MDS with Microsoft Active Directory.

Answer: A

NEW QUESTION 17
Refer to the exhibit. A switch is being downgraded to an earlier release because of a problem with the current release. After the switch is downgraded, it can no longer forward traffic. Which action resolves the issue?

• A. Enable ISSD after the downgrade is complete.
• B. Roll back to the original image.
• C. Reload the switch.
• D. Shut and no shut the interfaces to the FEX.

Answer: B

NEW QUESTION 18

Refer to the exhibit. The EEM script fails to send an SNMP trap when a user attempts to enter configuration mode. Which configuration is missing from the script?

• A. event statement
• B. event-default action statement
• C. policy-default action statement
• D. IP address of the SNMP server

Answer: D

NEW QUESTION 19

Refer to the exhibit. Partial configuration from N9K-1 and N9K-2 is included. The client has two WANs connected. WAN-1 is for normal business-day activities.
WAN-2 is for server backups during nonworking hours of 1:00 a.m. to 5:00 a.m. daily.
The client says that at the scheduled time for backup, the data center server failed to use the WAN-2 link to back up the servers to the cloud backup system. What is the solution to this problem?

• A. The event timer must be written in epoch time format.
• B. The Cisco Nexus switch must be configured with one applet because a configuration with two applets will fail.
• C. The Cron entry must be configured without double quotes.
• D. The applet called “Backup” must include an action to remove the current static route.

Answer: D

NEW QUESTION 20
An engineer is implementing a storage VDC, but fails. Which two prerequisites must be in place before a storage VDC is implemented? (Choose two.)

• A. M-Series module
• B. ESSENTIALS license
• C. STORAGE-ENT license
• D. FCoE license
• E. F-Series module

Answer: DE

NEW QUESTION 21
A user reports that they cannot reach from a UCS server to an FC Storage array. Which command is used to test communication between an FCF and a target?

• A. fcroute
• B. traceroute
• C. fcping
• D. ping

Answer: C

NEW QUESTION 22
Refer to the exhibit. A network engineer configures an EEM script to get a syslog notification after a configuration change. This message appears when the engineer must make a new configuration to this switch. Which configuration did the engineer neglect to apply in the script for it to function properly?

• A. event cli match ‘configure terminal’
• B. event policy-default count 1 time 100
• C. event syslog occurs 10
• D. action 2.0 event-default

Answer: D

NEW QUESTION 23
An engineer is troubleshooting a custom AV pair that was created by a client on an external authentication server to map a read-only role for a specific security domain. Which AV pair solves the problem?

• A. shell:domains=Security_Domain_1//Read_Role_1|Read_Role_2
• B. shell:domains=Security_Domain_1/Write_Role_1|Read_Role_2
• C. shell=Security_Domain_1/Read_Role_1|Read_Role_2
• D. shell:domains=Security_Domain_1/Read_Role_1|Read_Role_2

Answer: A

NEW QUESTION 24
A customer configures HSRP between two data centers that are interconnected with OTV. The configuration succeeds, but traffic between two ESXi virtual hosts on the same site is routed suboptimally through the OTV overlay. Which two actions optimize the traffic? (Choose two.)

• A. Disable first-hop redundancy.
• B. Filter HSRP traffic by using a Layer 3 VACL on the OTV edge devices.
• C. Filter HSRP by using a Layer 2 MAC-list on the ESXi vSwitch.
• D. Filter HSRP traffic by using a Layer 3 VACL on the ESXi vSwitch.
• E. Filter HSRP by using a Layer 2 MAC-list on the OTV edge devices.

Answer: AB

NEW QUESTION 25
......